Your cart is currently empty!
Wash care instructions to meet Páramo Guarantee conditions.
As with all technical clothing, caring for it correctly – and regularly – is central to its performance. Many outdoor garments have a Durable Water Repellent (DWR) coating applied to them that not only provides waterproofing but is essential for breathability. Repeat use, and dirt, dust, sweat, oils from animals, sunscreen and makeup can all build up over time and prevent the DWR from working properly.
The washing process is easy, and preparation is quick. First, wipe any excess dirt off your garment, secure zips, fasten tabs and loosen any elastics. Then, ensure your washing machine tray is clear of detergent and fabric softener residues. Use the correct Nikwax® product for your garment (see below) and wash it on a low temperature setting. At the end of the wash cycle, run your garment under a tap while it is still wet to check if water beads up on the outer fabric. If it does not, use the correct waterproofing product for your garment (see below) and use the same cycle setting as for the initial wash. At the end of the waterproofing cycle, leave your garment to air dry.
Our recommendation is to wash these garments using a warm, regular cycle. Do not wash on hot.
Washing:
Wash your garment regularly with Tech Wash® to ensure it is kept clean from dirt and contaminants and remains fresh. For most people this should be approximately every 3 months, however, if you wear your garment daily, we recommend you wash it once a month. You can never over-wash Páramo clothing – in fact, the more you wash it, the better it will perform and the longer it will last. It will also need reproofing less often.
Re-waterproofing:
You do not need to re-waterproof your garment after every wash. Rather, you should re-waterproof it with TX-Direct® Wash-in every 2-5 washes after cleaning it first with Tech Wash. We recommend checking the beading on your wet, freshly laundered garment after the washing stage to determine whether it needs to be re-waterproofed.
DO NOT use Tech Wash and TX-Direct in the same wash cycle!
Tumble drying:
While your garment can be tumble dried (low temperature, synthetic) it is not a performance requirement and we do not advise it. This is because both Páramo and Nikwax products are PFAS free and, therefore, do not require heat activation to deliver cleaning and waterproofing results. Instead, we recommend air drying your garment.
Trouble shooting:
If your garment is not re-waterproofing as you would expect it to, this is likely due to; insufficient washing, external contamination (such as from pack straps or airborne chemicals), over-proofing, or if the garment has not been cleaned properly first. For any problems you are experiencing, please contact our Customer Experience team.
Our recommendation is to wash these garments using a warm, regular cycle. Do not wash on hot.
Washing:
Wash your garment regularly with Tech Wash® to ensure it is kept clean from dirt and contaminants and remains fresh. For most people this should be approximately every 3 months, however, if you wear your garment daily, we recommend you wash it once a month. For Fleece and Wind resistor garments that are frequently worn next to the skin or over a baselayer, we recommend more regular washing. You can never over-wash Páramo clothing – in fact, the more you wash it, the better it will perform and the longer it will last. It will also need re-waterproofing less often.
Re-waterproofing:
You do not need to re-waterproof your garment after every wash. Rather, you should re-waterproof it with TX-Direct® Wash-in every 2-5 washes after cleaning it first with Tech Wash. We recommend checking the beading on your wet, freshly laundered garment after the washing stage to determine whether it needs to be re-waterproofed.
DO NOT use Tech Wash and TX-Direct in the same wash cycle!
Tumble drying:
While your garment can be tumble dried (low temperature, synthetic) it is not a performance requirement and we do not advise it. This is because both Páramo and Nikwax products are PFAS free and, therefore, do not require heat activation to deliver cleaning and waterproofing results. Instead, we recommend air drying your garment.
Trouble shooting:
If your garment is not re-waterproofing as you would expect it to, this is likely due to; insufficient washing, external contamination (such as from pack straps or airborne chemicals), over-proofing, or if the garment has not been cleaned properly first. For any problems you are experiencing, please contact our Customer Experience team.